Other TxDOT Documents
This handbook presents guidance information that may support or expand upon information contained in other TxDOT documents. The guidance contained in this handbook does not supersede standards, recommended practices, or requirements established by other TxDOT documents. The following documents also contain information related to the application, design, placement, installation, and maintenance of freeway signing:
Texas Manual on Uniform Traffic Control Devices (Texas MUTCD).
The Texas MUTCD establishes practices for the selection, design, placement, operation, and maintenance of traffic control devices. The Texas MUTCD is the document that establishes the legal requirements for the selection, application, design, installation, and maintenance of traffic control devices. Many of the figures in this handbook contain cross-references to the Texas MUTCD to identify the need or application of a specific sign. When a figure contains a cross-reference to the Texas MUTCD, the user should refer to the indicated section of the Texas MUTCD to determine the appropriate application of or need for the sign. The 2003 edition of the Texas MUTCD (released in January 2003) was used in the preparation of this handbook.
The 2006 Texas MUTCD was published after the completion of this handbook; however, an attempt was made to incorporate changes introduced in the 2006 Texas MUTCD into this handbook. The Texas MUTCD is available on-line at
.
Traffic Engineering Standard Sheets.
The Traffic Engineering Standard Sheets developed by the Traffic Operations Division (TRF) contain additional guidance for the design, placement, and mounting of freeway guide signs. Where appropriate, figures in this handbook reference the standard sheets. The Traffic Engineering Standard Sheets are available on-line at:
.
The following 3 tables list standard sheets pertinent to subjects related to freeway guide signs.
Sheet Name | Subject |
|---|---|
TSR(1) | Requirements for Overhead and Large Ground Mounted Signs |
TSR(2) | Requirements for Attachments and Exit Panels to Guide Signs |
TSR(3) | E, D, and I Series Guide Signs |
TSR(4) | Requirements for Blue and Brown D Series Guide Signs and Independent Mounted Route Markers |
TSR(5) | Requirements for Regulatory and Warning Signs |
TSR(6) | Typical Attachment and Arrow Details |
WSSFT | Weigh Station (Freeways Trucks Only) |
CSSFB | Check Station (Freeways Trucks/Buses) |
Sheet Name | Subject |
|---|---|
OSB-SE | Selection Examples |
OSB-Z1 | Sheet 1 of 3 (Bridge Details) |
HOSB-Z1 | Sheet 1 of 3 (High Level Bridge Details) |
HOSB-Z1L | Sheet 1 of 3 (High Level Bridge Details) |
OSB-Z2I | Sheet 1 of 3 (Bridge Details) |
HOSB-Z2I | Sheet 1 of 3 (High Level Bridge Details) |
OSB-Z3 | Sheet 1 of 3 (Bridge Details) |
HOSB-Z3 | Sheet 1 of 3 (High Level Bridge Details) |
OSB-Z3I | Sheet 1 of 3 (Bridge Details) |
HOSB-Z3I | Sheet 1 of 3 (High Level Bridge Details) |
OSB-Z4 | Sheet 1 of 3 (Bridge Details) |
HOSB-Z4 | Sheet 1 of 3 (High Level Bridge Details) |
OSB-Z4I | Sheet 1 of 3 (Bridge Details) |
HOSB-Z4I | Sheet 1 of 3 (High Level Bridge Details) |
OSBT | Sheet 2 of 3 (Bridge Tower Details) |
OSBC | Sheet 3 of 3 (Bridge Truss Details) |
OSBC-SC-Z1 | Sheet 2A of 3 (Bridge Truss Details) |
OSBC-SC-Z2 | Sheet 2A of 3 (Bridge Truss Details) |
OSBC-SC-Z3 | Sheet 2A of 3 (Bridge Truss Details) |
OSBC-SC-Z4 | Sheet 2A of 3 (Bridge Truss Details) |
OSBS-SC | Sheet 2B of 3 (Single Column and Drilled Shaft Reinforcing) |
OSB-FD | Foundation Embedment Selection Charts |
OSB-FD-SC | Foundation Embedment Selection Charts |
COSS & OSB-SZ | Sheet 1 of 3 (Special Cantilever and Bridge Details) |
COSS-SE | Selection Example |
COSS-Z1 | Sheet 1 of 3 (Cantilever Details) |
HCOSS-Z1 | Sheet 1 of 3 (High Level Cantilever) |
COSS-Z2I | Sheet 1 of 3 (Cantilever Details) |
COSS-Z3&Z3I | Sheet 1 of 3 (Cantilever Details) |
COSS-Z4&Z4I | Sheet 1 of 3 (Cantilever Details) |
COSSD | Sheet 2 of 3 (Support Details) |
COSSF | Sheet 3 of 3 (Foundation Details) |
COSS-FD | Foundation Embedment Selection Charts |
ED(1) thru ED(13) | Electrical Details |
SL(MV)-93 | Mercury Vapor Sign Light Fixture |
SL(1)-95 | Sign Lighting (Electrical Details) |
SWW(1) | Sign Walkway and Handrail |
SB(SWL-1) | Support Bracket Details |
Sheet Name | Subject |
|---|---|
FPM(1)-00A | Typical Standard Freeway Pavement Markings — Raised Markers |
FPM(2)-00A | Typical Standard Freeway Pavement Markings — Entrance and Exit Ramps |
FPM(3)-00A | Typical Standard Freeway Pavement Markings — Lane Drop Exit Ramps |
FPM(4)-00A | Typical Standard Freeway Pavement Markings — Lane Drop Exit Ramps |
Standard Highway Sign Designs for Texas.
The Standard Highway Sign Designs for Texas
(Texas SHSD) presents the dimensions needed to fabricate individual standard signs. This document primarily addresses signs with a standard layout (such as regulatory and warning signs). Appendix F of the Texas SHSD includes information on the design of large freeway guide signs. That information has been incorporated into this handbook. Revision 4 (December 1998) of the Texas SHSD was used to prepare this handbook. The standard signs shown in the handbook figures are provided for illustrative purposes only. Every effort has been extended to ensure that the appearance of the standard signs in these figures is an accurate representation of the actual sign design. The Texas SHSD should be used to determine the design and layout of standard signs. The Texas SHSD is available on-line at
.
Signs and Marking Volume of the Traffic Operations Manual.
The Signs and Marking Volume
sets forth TxDOT standard practices and procedures regarding signs, markings, and other traffic control devices. This manual supplements the information contained in the Texas MUTCD. The November 1997 version of the Signing and Marking Volume
(with the May 2000 revision of Chapter 10) was used to prepare this handbook. Sign Crew Field Book.
The Sign Crew Field Book
provides field crews with information on the placement and installation of signs on conventional rural highways. The January 2000 version of the Sign Crew Field Book
was used to prepare this handbook.